Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
What is the gage pressure at this depth in fresh water, and what is the ratio of absolute pressure at this depth to normal atmospheric pressure? Assume Temp. = 20 C.
A gage on an oxygen tank reads a pressure of 300 kPa gage. What is the pressure in the tank in kPa abs? please show the work and include units.
The temperature outside is 0 C. If it is calm and the heat exchange coefficient is h = 5 W/m2· K, what is the rate of heat transfer in kJ/s from your hands?
Evaluate the coefficient of performance. Assume Cv for the gas is 3/2*R, where R is the ideal gas constant. Path 3->2 is isothermal and Path 4->3 is adiabatic.
What is the specific volume of this R-22 initially? b) What is the quality of this R-22 after the cooling? c) What is the internal energy U after the cooling?
If the rods are 1.5 inches in diameter and the allowable stress of the steel used is 80,000 psi, what is the safety factor of this design?
Determine the time constant of this thermocouple. If the gas temperature suddenly increases by 100 C, how long will it take the thermocouple to attain a temperature rise within 1% of the gas temper
The spring constant on car A is k= 3MN/m. Determine the maximum compression of the spring mounted on car A. neglect rolling resistance.
The top surface of the oil in the manometer is even with the water surface inside the tank. If the ambient pressure is 14.5 lbf/in2, what is the air pressure above the water surface in the tank? The
What is the ratio of the two weights? Assume that the earth is a perfect sphere with radius 'R' and that the spin axis is the geographical North-South axis.
The retarding force due to the fluid is proportional to the square of the velocity of the pendulum. Call the constant of proportionality k. Derive the equations of motion for the pendulum.
Determine: a. The temperature of the air at the compressor exit. b. The heat transfer in kJ/kg of air flowing c. sketch the process on a p-v and T-s diagrams and indicate the work and heat transfers
The water is expanded isothermally until the quality is 80%. Determine the work produced by the expansion. Do not assume water to behave as an ideal gas. ( W is not equal to RT(ln(v2/v1))
Then in another 4 s it moves from sB to sC = +2.5m. Determine the particle's average velocity and average speed during the 6-s time interval.
If the mean thickness is 3mm and the standard deviation is 0.25, calculate the percentage of gaskets that have a thickness greater than 2.5mm.
Saturated vapor at 150 kpa. It is heated to 40 C, and the steel is at the same temperature as the R-134a at any time. Find the work and heat transfer for the process.
Compute the required diameter of the wire. Neglect the weight of the wire. Use E = 207 000 MPa and a proportional limit of 234 MPa.
Compute the maximum tensile stress due to the bar's own weight and the maximum load P (the allowable load) that can be safeley supported at the lower end of the bar if the allowable tensile stress is
Calculate the period and the frequency of rotation for the object. Calculate the centripetal force required to rotate a 3kg mass in a 6m diameter circle at one 60 revolutions per minute.
Assuming the heat transfer to be at steady state, what thickness of insulation should be put on the duct to keep the rate of heat gain by the refrigerated air per meter length of the duct to 30 W?
Consider air parcel moving upwards. a) What will be the air parcel's temperature be at 2 km altitude, if the surface temperature of the air parcel is 25°C? b) What will be the parcel's temperat
What is the relative humidity (RH) of an air parcel with temperature 25°C and absolute humidity 8 g/m3? See class 4 notes posted to Blackboard for saturation pressure equation.
Assume that the actual density of the washers is 7.81 g/cm3. What is the percent error of your calculated mean? What sources of error exist in this experiment?
Determine the steady state rate of heat transfer per unit area through a 4.0 cm thick homogeneous slab with its two faces maintained at uniform temperature of 38 degrees C and 21 degrees C.
Calculate the time until it reaches 400C. what is the pressure then? Draw the process on a Pv and Tv diagram with respect to the saturation line.