Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time req
Two homogeneous isotropic dielectrics meet on plane x=0. For x > 0, Er1=6 and for x<0, Er2=3. A uniform electric field E1=3ax-2ay+5az V/m exists for x >0. Find: a) E2 for x<0 b) The angles
Telephone signals are typically sampled at 8000 Hz. a. What is the time interval between samples b. What is the highest frequency that can be recovered from a sampled signal
Identify the type of cable that is permitted in single- and multifamily dwelling units but that cannot be used underground, nor in buildings that are more than three stories above grade, nor in comm
The above transformer is to be connected as an auto transformer to supply a load at 120 V from 210 V source. What kVA load can be supplied without exceeding the current rating of the windings
If these nominal non--ideal parameters are replaced, one at a time, by A = 50000, Ri = 1 M and R0 = 150 (each of which is twice as bad as the nominal values), which parameter has the largest impact
The transformer secondary is now connected to a purely resistive load drawing 50A. Calculate: a) the total resistance and leakage reactance values referred to the secondary (Rt2 and Xt2), b) the outpu
A 230V shunt motor having an armature resistance of 0.05 and a field resistance of 75 draws a line current of 7 A while running light at 1120 rev/min. The line current at a given load is 46 A.
The resistance of the field circuit of a shunt-excited dc generator is 200. When the output power of the generator is 100kW, the terminal voltage is 500V and the generated e.m.f is 525V.
An additional variable power factor load is to be added to the factory. The new load will add 320 kW to the factory. The power factor of the variable power factor load is to be adjusted so that the
A ball is thrown upwards with a velocity of 31 m/s at an angle of 35.5 to the horizontal from a point which is 8 m above ground level. Find: 1) The greatest height reached, above the point of projec
Suppose we want to construct an amplifier with a closed-loop gain of 50. We want the gain to vary by no more than +/- 5% while the open-loop gain varies by +/- 50%. Determine the values for a and b
A PWM is to be programmed to output a signal with a pulse high width of 150 usec and a pulse low width of 250 usec. What are the values required for prescale (if any) PWMPER and PWMDTY An 8-bit conf
A circuit consists of a battery connected to three resistors (60ohm , 30ohm , and 180ohm ) in parallel. The total current through the resistors is 1.9A . Find the emf of the battery.
Assume that the load is star connected with the neutral disconnected. Each phase has a series RL load with R = 5 ohms and L = 20 mH. Plot the neutral voltage Plot the phase to neutral voltage for pha
A sample of non-ideal gas is made to undergo an expansion process during which its pressure and volume are related as shown in the table below. The energy of the gas at the start and finish of the p
A substance expands from V1 = 1 ft3 to V2 = 6 ft3 in a constant-pressure process at 100 lbf/in2. The initial and final internal energies are U1 = 40 Btu and U2 = 20 Btu, respectively.
A certain signal is modeled by a continuous Gaussian random process X(t) with mean E {X(i)} = 2 and autocorrelation function R(t, r) = 4 + e-0.5|r|. Compute the covariance function C(t, r). Compute
Consider a VBE multiplier with R1=R2= 1.2k ohms utilizing a transistor that has VBE= 0.6V at Ic = 1ma, and a very high beta. (b) Find the value of the current I that will result in the terminal volt
The power factor of a load connected to a 120-V 60-Hz source is raised from 0.866 lagging to 0.966 leading by connecting a 110.5-F capacitor in parallel with the load. Determine the load current I1
Find the equivalent impedance for Z1 = 60 L+60 and Z2 = 80 L-45 when these are connected in parallel What are the branch currents and the total circuit current if the supply voltage to the circ
A series RLC circuit connected to a 100-V 60-Hz source draws a current of 2.5 A. The measured power factor for the circuit is 0.7 leading, and the inductive reactive power is 300VAr. Calculate the
The input/output relation of a discrete time system is given by y(n) = x(n+1) + x(n-3). Find an expression for h(n), the unit sample response of this system. specify how many non-zero terms t
An additional variable power factor load is to be added to the factory. The new load will add 320kW to the factory. The power factor of the variable factor load is to be adjusted so that the overall
The power factor of a load connected to a 120-V 60-Hz source is raised from 0.866 lagging to 0.966 leading by connecting a 110.5-?F capacitor in parallel with the load. Determine the load current I1