Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
air expands through a nozzle at a rate of 1kg/sec. the outlet is at 15kpa and the inlet is at 400kpa,150degree and 35m/sec. assuming the process to be reversible and adiabatic, what is the exit velo
For the PMOS, calculate the applied voltage and the electric field (at the Si-SiO2 interface) to make the silicon surface intrinsic. What is the depletion width in this case.
a) Detrmine Frequency response of a 3rd order high-pass filter having a cutoff freq at 150hz. b) Detrmine freq response function of 4th order low-pass filter ahving cutoff freq at 600hz.
The output/ input of a system is 30dB. detrmine the ratio Express x(t)=4*cos(100*t-45)+ 2*cos(250*t+30) in terms of exponential functions Then Detrmine the phase angles(in degrees) of the two freque
The signal x(t)=10cos(t)+10sin(10t) is input into the following systems: a) \(H(s)=100/(s^{2}+10s+100)\) b) \(H(s)=s^{2}/(s^{2}+10s+100)\) calculate the output for each system.
design a sequential circuit that continuously computes the function 2X + 3 or 3X + 1 where the variable X is a three-bit unsigned integer available on a serial interface. A special external data sig
Using Floating Point Unit and the switch statement Create an HLA program to perform the following: -Two data conversions (decimal,binary,hex) -Two measurement calculations (miles,feet,meters,inches) -
Design a 3-bit counter using D flip-flops to cycle through the following sequence: 010, 101, 110,001. Make sure the counter is self-starting.
Write the full equations to light the bottom segment of a 7-segment display. INLCUDE the hexadecimal digits too ( b, c, d, and E ). Then simplify the equations using a k-map and draw the final circu
In a 120V compound generator, the resistances of the armature shunt and series windings are 0.06 ohm, 25 Ohm, and 0.04 Ohm respectively. The load current is 100A at 120V, find the induced EMF and th
A 25KW, 250V dc shunt generator has armature and field resistances of 0.06 ohm and 100 ohm respectively, determine the total armature power developed when working (1) as a generator delivering 25KW
when an AC source is connected accross a 12.0 resistor,the rms current in the resistor is 8.00 A find (a) the rms voltage accross the resistor,(b) the peak voltage of the source , (c) the maximum c
For PID control, what are roles of integral term and derivative term. Given KP=10, KI=3, and KD=4, write down this PID controller function.
Consider a system equation \(s^{4}+s^{3}+s^{2}+2s+10=0\) Find its Routh Table. Determine if the system is stable , marginal stable, or unstable.
A small buck converter has 24 V input and 12 V output. The transistor has Rds(on) - 0.1 Ohm. The diode is modelled as a 1.0 V drop. Each device has junction to ambient Rtheta(ja) = 40 K/W and Tjunct
A boost converter has 5 V input and 12 V output at 60 W. The diode is ideal. The transistor requires 1 us to turn on and off. The switching frequency is 100 kHz. The storage components are large.
A MOSFET is used in a boost-buck converter. The on-state loss is 4.2 W, and the switching loss is 2.8 W. The device is in TO-220 heat-sink package. it is desired to avoid a heat sink, and a parallel
What is the frequency response analysis. Which two parameters are used to determine frequency response. Draw Bode Plot for G(jw) = 10 (jw + 3) / [(jw)(jw + 2)]
Given transfer function of dynamic system: T(s)= (2s^2 + 2s + 3) / (s^3 + 4s^2 + 6s + 10). write down state equation and output equation in Controllable Canonical Form and in Observable Canonical F
Consider a system equation s^4 + s^3 + s^2 + 2s + 10 = 0. FInd out its Routh Table. Determine if this system is stable, marginal stable or unstable. How many roots are stable and how many roots are
A DC motor has a terminal voltage of 5V, a motor constant of Ka = 5.2 x 10-3 Vs, and an armature resistance of 500-ohm. Find the stall current, max speed in rotations per minute (RPM), and armature
a) Draw a cascade or parallel form for the block diagram representation of the system b) Determine the possible ROC's of this system. For each case determine causality and stability of the system.
The Integrator and Differentiator appear to behave like analog filters. What kind of filters are they, how do they behave with low and high frequencies
For a circuit we would like to implement, there are two control signals: x and y. If xy = 01, an 8-bit value R is incremented by 1 and control goes to a second state. If xy = 10, R is cleared to zer
1. For a triangular waveform, with a peak amplitude of 2V, a width of 10ms, and a period of 10 ms a. Draw the waveform. b. What do you think the average value will be for this waveform