Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
A single-phase load is supplied with a sinusoidal voltage v(t) = 200 cos(377t) The resulting instantaneous power isp(t) = 800 + 1000 cos(754t ¡ 36:87±) (a) Find the complex power su
Determine the expression for the frequency response H(Omega) of a causal IIR LTI discrete-time system characterized by the input-output relation. where |a|<1, and y[n] and x[n] denote, respectivel
design a stable optical cavity using one mirror with infinite radius of curvature and 95% reflectivity. We want the cavity to 1 m long. Assume the second mirror is 100% reflective. a. Design the cav
A 2 farad capacitor is charged up to 400v by a dc power supply. How long in seconds would it take to discharge the capacitor to a safe stored energy level of 1 joule using a 1k ohm high wattage resi
Determine the expression for the frequency response H(O) of a causal IIR LTI discrete-time system characterized by the input-output relation y[n]=x[n]-ay[n-R], |a|<1, where y[n] and x[n] denote r
1- what is meant by plug and ply devices what are the bus protocols that support plug and play devices 2- what is hot attachment and detachment what are the bus protocols that support hot attachment a
1- a port device may have multi-byte data input buffers and data output buffers. what are the advantages of these 2- what are the advantages of DAA(Data Access Arrangement) and McBSP ports in DSPs
Determine the relative probability of finding the electron at the distance (a) 12 A beyond the barrier, and (b) 48 A beyond the barrier, compared to the probability of finding the incident particle
Design a circuit that takes the output from each of the five microphones your band uses and adds the voltage to create a single voltage signal which is fed to the amplifer. Except not all voltages
Design a circuit that will calculate the value for the average voltage for three input signals. Draw the circuit schematic identifying supply voltages and show your work on component selection.
Create the layout design for MOS inverter using a depletion-type transistor with VTL = -0.3V and an enhancement-type device with VTO = 0.5V such that tPLH is less than or equal to 15ns and tPHL is l
Along the way to the page, they pass into a region between two deflecting plates that are 1.6 cm long. There is a 1,500,000 N/C electric field between the deflecting plates. You measure the distance
Given a four-volt peak to peak square wave, calculate the mean-square error in approximating the wave by only its fundamental sinusoidal component. Assume the average value is zero (no DC offset).
Consider a 32-bit microprocessor whose bus cycle is the same duration as that of a 16-bit microprocessor. Assuming that, on the average, 20% of the operands and instructions are 32 bits long, 40% a
There are three gates. Each gate can be opened or closed depending on the three logic inputs: (a, b, c). Gate open logic=1, gate close= logic 0. Design a logic circuit so that no adjacent gates or o
1. which would have a higher line reactance in ohms. An overhead 138KV line or an overhead 34KV line. Why. 2. Does line charging amps increase or decrease with line length. Why
1. can a transformer ratio LTC control MW or Mvar power flow on a parallel transformers 2.what test is used to calculate a transformer through fault impedance 3. List three design or operating factors
In order to control the slope of a ramp produced by an integrator, the values of Vin, R, and C may be varied. Assuming a fixed value for C of 10 μF, would it be better to have a relative large Vi
A M-bit thermometer code for the number k consists of k 1's in the least significant bit positions and M-k 0's in the more significant bit positions. A binary-to-thermometer code converter has N inp
A 240/40 volt transformer supplies two different secondary loads. One load (a) draws a current of 12 amperes at a lagging power factor of 0.94. The other load (b) draws a current of 12 amperes at a
The lighting and motor loads of a small factory establish a 10kVA power demand at 0.7 lagging power factor on a 208V, 60 Hz supply. Determine the power-factor capacitor that must be placed in paralle
Develop the pseudo-code below for a program that will retrieve 2 bytes (NUM1 and NUM2) from memory, determine which is closest to the numeric value 50, and indicate the result by setting a variable
A Thevenin equivalent can also be determined from measurements made at the pair of terminals of interest. Assume the following measurements were made at the two external terminals a, b of a circuit.
Calculate( show all details, including Input versus Output voltage curve) and indicate all circuit required circuit parameter values in order to achieve both positive and negative output bounds as s