Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
it is required to establisg a chart for count of nonconformities for a manufacturing process. if 25 units are to be inspected and the total number of the count of nonconformities from all the units
At time t = 0 an electron at the origin is subjected to a force that briefly accelerates it in the +z direction, with an acceleration of 6 × 1017 m/s^2. Before trying to answer the following q
A 2-input NOR gate has inputs A and B. If the output of the gate remains LOW independent of the state of input A, what can be deduced about B
1. What would you need to understand about a CPU's architecture to take pseudo-code and convert it into programming instructions 2. What files are generated by CodeWarrior when you assemble an
implement the Johnson counter as a Moore machine using three (3) D flip-flops. Give the simplified excitation equations for each of the flip-flops, and draw the circuit. There is no input in this sy
Assume A is the MSB and B is the LSB. The circuit produces an output of 1 if and only if the sum of the current 2-bit input and the previous 2-bit input is equal to 6. Design the circuit using as fe
A sequential circuit has two inputs (A and B) and contains one JK flip-flop that has only JK and clock inputs. If A = B the flip-flop is unchanged, otherwise the flipflop is complemented. Find the e
A sequential circuit has two inputs (A and B) and contains one D flip-flop that has only D and clock inputs. If A = B the flip-flop is unchanged, otherwise the flipflop is complemented. Find the exc
design the logic to control the temperature in a green house. the temperature between 72 degrees and 80 degrees if the tem is below 72 degrees, a heater must be activated if the tem is above 80 degr
obtain the rotational losses of a universal motor if you are only given the impedance, RPM, voltage,poles, frequency, current and pf Basically I need to solve for the shaft torque and efficiency but
Design an embedded system to turn on an LED when it is dark and turn off of LED during the day time.
Fundamentals of Electric Circuits fourth edition: alexander, sadiku chapter 12 problem 12.29 A balanced three phase wye-delta system has Van= 120 angle 0 Vrms and Zdelta= 51+ j45 ohms. if the line i
obtain, via the bilinear transform, the coefficients of a digtal filter that is maximally flat in the passband, 0 to 4 kHz, and has an attenuation of at least 25 dB at frequencies over 10 kHz. Assum
Let S measure the time-dependent strength of a material under test and So is the initial strength as measured at the beginning of test. Prior tests and evaluations have suggested that the following
An electron describes periodic oscillations in the direction of the axis "z" with amplitude of 1 nm (nano meters) around a ring, if the ring has a total charge of 100e with a radius of 50 nm (nano m
A 100 Hz electromagnetic wave is propagating down into the sea water with an electric feld intensity of |E| = 1 V /m just beneath the sea surface. a. What is |E| at a depth of 100 m b. What is the t
The complex permittivity for bottom round steak is about epsilon = 40(1 - j0.3)*epsilon0(e0) at the operating frequency (2.5 GHz) of a microwave oven. What is the penetration depth
A single-phase circuit is placed across a 120-V rm, 60-Hz source, with an ammeter, a voltmeter, and a wattmeter connected. The instrucments indicate 12 A, 120 V, and 800 W, resppectively. Find (a) t
Suppose that the machining operation requires 1 kW, that the tool machine ihas 90 percent efficiency, and that the supply current is 14 A rms with a power factor of 0.8. Find the AC machine efficien
A current of 4 A rms flows when a neon sign is supplied by a 110-V rms power system. The current lags the voltage by 60°. Find the power dissipated by the circuit and the power factor.
The heating element in a soldering iron has a resistance of 30-ohm. Find the average power dissipated in the soldering iron if it is connected to a voltage source of 117 V rms.
An RL circuit consists of a switch, an emf source Eo, a 4 k-ohm resistor, and a 3 H inductor. If the potential across the resistor is 96 V 6 ms after the switch is closed, find the source emf, Eo.
Determine the complex power for the following cases: (a) P = 269 W, Q = 150 VAR (capacitive) (b) Q = 2000 VAR, pf = 0.9 (leading) (c) S = 600 VA, Q = 450 VAR (inductive) (d) Vrms = 220 V, P = 1 kW,
Consider a discrete time system whose output y[n] is given by y[n] = 5/6y[n - 1] - 1/6y[n - 2] with y[-1] = 0 and y[-2] = 1. Determine the response y[n] of this system for all n using complex domain
Instrumentation amplifiers are indeed constructed with either 2 Op Amps or 3 Op Amps. Does that mean that the 3 Op Amp is more common