Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
Design an amplifier circuit that will selectively amplify dolphin social conversations. The microphone can be modeled as a sinusoidal voltage source with peak amplitude less than 15 mV in series wit
A 5-MVA, 66:13.2kV, three-phase transformer supplies a three-phase resistive load of 4,500kW at 13.2kV. What is the load resistance in ohms as measured from the line-to-neutral on the high-voltage s
consider the set of activities, duration (in days), and predecessors for a project given below. a) Develop a network diagram representation for the project. b) Determine the critical path. c) Determin
Develop a functional design for a system that measures and displays the speed of a bicycle. Be sure to clearly identify the design levels, function requirements, and theory of operation for each lev
Let E = yax V/m at a certain instant of time, and calculate the work required to move a 3-C charge from (1,3,5) to (2,0,3) along the straight-line segments joining: a) (1,3,5) to (2,3,5) to (2,0,5)
An RC electric circuit is to have a rise time of one microsecond (1 μs). Select appropriate values of R and C to accomplish this objective.
What is the formula for finding the output voltage of a non-inverting summing amplifier with 3 inputs
A network has an input impedance of 120+100j Ohm what is the capacitance that should be placed in parallel with the network to provide an input impadance with: a) Zero Reactance at w=1000 rad/s b) Zer
A network has an input impedance of 120+100j Ω what is the capacitance that should be placed in parallel with the network to provide an input impadance with: a) Zero Reactance at w=1000 rad/s b)
A CB amplifier is operating with R load = 10 kiloohms, Rc = 10 kiloohms, and R signal = 100 ohms. At what current Ic should the transistor be biased for the input resistance Rin to equal that of the
An emitter follower is operating at a collector bias current of 0.25 mA and is used to connect a 10 kiloohm source to a 1 kiloohm load. If the nominal value of beta is 100, what output resistance Ro
Determine which waveform in each pair is lagging: a) 6 cos(100πt-1000) and -6 sin (2π60t+1300)b) cos(10t-1000) and - cos(t-1000) c) cos (50πt - 1000) + cos (50πt - 200) and 9 cos (100πt
the donor energy level is approximately 0.1 ev below the conduction band. the approximate value is calculated from the binding energy equation from hydrogen. derive the binding or ionization energy
a) determine the wave equations for all three regions b) what is K for each region c) using matrix algebra, determine the coefficients to the wave eaquation in region 2
A 3-kVA, 220:110-V, 60-Hz single-phase transformer yields this test data open-circuit test: 200 V, 1.4 A, 50 W short-Circuit test: 4.5 V, 13.64 A, 30 W Determine the efficiency when the transformer de
Identify five controls that require the operator to do two destict actions in order to activate the control? EXAMPLE depressing the clutch on a car so that the ignition key will start the car.
(a) the conductivity in a p type silicon semiconductor at T=300 K is sigma=0.25 (ohm-cm)^-1. Determine the thermal equilibrium values of electron and hole concentrations. (b) Repeat part (a) for n t
Implement the carry-out and sum functions for a 1-bit full adder using a 3-to-8 decoder block with active-low outputs and additional gates (what gate types should be used). Complete the truth table
An ideal one sided silicon n+p junction has uniform doping on both sides of the abrupt junction. The doping relation is Nd=50Na. the built in potential barrier is Vbi=0.752 V. the maximum electric f
Determine the transmission coefficient for the system for X=a where a is on the order of nanometers. Determine the transmission coefficient for the system for X=a where a is on the order of meters
A silicon abrupt junction in thermal equilibrium at T=300 K is doped such that Ec-Ef=0.21 eV in the n region and Ef-Ev=0.18eV in the p region. (a) draw the energy band diagram of the pn junction.
Use rail voltages of +/-15V. Sketch the circuit diagram and the voltage transfer characteristic (Vout vs Vin) Discuss how you chose the values of the components and comment on how accurately you thi
A balanced Y-connected three-phase motor uses 20 kW of power at 0.81 pf lagging when connected to 220 V lines. What is the line current. What is the current in one phase of a delta-connected generat
a) A delta-connected three-phase source has a phase voltage of 220 V. It feeds a delta-connected load consisting of three identical impedances of 10/42° O each. Find the magnitude of the phase c
Suppose the volume X occupied by a capacitor is A*d where A is the total area of the dielectric layers and d is the thickness of each dielectric layer (this assumes that the metal plates are infinit