Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
Use a K-Map to design a circuit that will accept 5-bit input, and output the value left-shifted by 1. For example, if the input is 10101, the output is 01010. Design a circuit that implements this f
what are the octal values of the four 8-bit bytes in the 32-bit number with octal representation 321076543218
An isolated free electron is traveling through an electric field from some initial point where its coulombic potential energy per unit charge (voltage) is 17 kJ/C and velocity = 93 Mm/s to some fina
The binary-coded-decimal (BCD) format uses 4 bits to represent 10 decimal digits. For example, 259 in base 10 is repesented as "010 0101 101" in BCD format. A BCD incrementor adds 1 to a number in B
A ROM chip of 1024 X8 bits has four select inputs and operates fron a 5 volt power supply. How many pins are needed for the IC package. Draw a block diagram and label all input and output terminals
1. How would you bias a BJT in a common emitter amplifier in order to minimize the Miller feedback capacitance 2. Explain how it is possible to identify the different current transport mechanisms.
Identify three test cases, one using a positive number, and one using a negative number, and one using incorrect input (ie. Input a letter rather than a digit for the numeric input). For each of the
A repeater with additive noise of 48μW and a power gain of 20 dB has 150μW of input signal power and 1.2μW of input noise. Calculate the input SNR, the output SNR, the noise factor, and the
Two loudspeakers, one of them generates sound 400W power the other with 100W. The sound is generated isotropically from each loudspeaker. A listener is seated 20 m from the 100 W loudspeaker and 40
1. Find IC, IE and IB for a PNP transistor if IS = 10-16 A, ßF = 75, ßR = 0.40, VEB = 0.75V and VCB = +0.70V. 2. The total transport current iT traversing the base of a BJT is determined b
The total trace length on the printed wiring board between the IC power and ground pins and the decoupling capacitor is 1 in. a)To the limit the voltage transient of the IC to 0.01V, what is the minim
Write a program to compute the impedance Z and the inductance L of an electrical coil, given the voltage V, current I (amps), resistance R (ohms), and frequency F (cycle/second). Make use of selecti
what is the minimum value decoupling that should be used. for the value of capacitor determined in part "a" estimate the self-resonant frequency of the capacitor, printed wiring board trace combinat
Water is being heated in a vertical piston-cylinder device. The piston has a mass of 15 kg and a cross-sectional area of 120 cm^2. If local atmospheric pressure is 99.5 kPa, determine the temperatur
(1) a lighting load drawing 10kW, (2) an induction motor drawing 10 kVA at 0.9 power factor lagging, and (3) a synchronous motor operating at 10 hp, 85% efficiency and 0.95 power factor leading (1 h
Plot the reflection coefficient for 4 pairs of quarter-wave coated substrate for acrylic/diamond coating-pairs on fused silica substrate. Your plot should be as a function of wavelength range from 4
Use decomposition to find the minimum gate input cost, multiple level implementation for the functions given, using AND, OR, NOT, XOR gates: a) F(A,B,C,D)=sigma(m)(5,6,7,9,10,11) b) G(W,X,Y,Z)=sigma(
John's friend Sven has an "automatic crossover" power supply that can output up to 50V and up to 12Amps. What is the output voltage and current of the supply when John connects a 3O resistor to Sven
Assume that a resistor depicted by a color code of Brown, Black, Orange (1%) is connected to the +15 V and AGND terminals of MyDAQ. And assume that the Digital multimeter of MyDAQ shows the voltage
What is the current if the voltage source is reduced to 80% of the original value. Will the current increase or decrease and by how many percent if the total resistance of the circuit is 10% of its
a.) The current in a 75 mH inductor changes uniformly by 200 mA in 0.1 ms. What is the voltage across it b.) Determine the inductance of an air core coil with length 20 cm, 200 turns and a diameter of
A test charge q located at the origin is displaced by a distance l << d along the positive x-axis. Find an approximate expression for the electric force acting on the charge.
A p-channel MOSFET with a threshold voltage V,p = -0.7 V has its SOUTce connected to ground. (a) What should the gate voltage be for the device to operate with an overdrive voltage of Ilor! = 0.5 V
The voltage across a 1-µF capacitor is given by v(t)=100 e-100t . Find expressions for the current, power, and stored energy. Sketch the waveforms to scale versus time.
For a 32 bit CMOS 5 volt microprocessor that has a 32 bit address bus and a separate 32 bit data bus, and the processor has a 1 nS rise time and 0.5 nH of ground inductance on a board made from glas