Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
The D-Latch is constructed with four NAND-gates and an inverter. Consider the following three other ways for obtaining aD-Latch, and in each case draw the logic diagram and verify the circuit operat
a. Draw thee logic diagram of the circuit b. Determine the FSM type of this clocked Synchronous Sequential Machine c. list the state-table for the sequential circuit d. draw the corresponding state di
An Opamp has a low frequency gain of 10^5 and a high frequency response with a single pole at 100 rad/s and a pair of poles at10,000 rad/s. (a) At what frequency does the total phase shift reach 180
Using the switch-resistor MOSFET model, design an invertersatisfying the static discipline for the four voltage thresholds using an n-channel MOSFET with RN=1KΩand VT=1.8v. Recall, RON=RN(L/W)
Given that the resistors that can be used in the lab have a maxpower rating of 1/8W and the logical voltage values will be 0V or5V at the input, determine an appropriate size for the requiredresisto
In an op amp circuit, how is it possible that the power delivered to the circuit by two voltage sources is smaller than the power absorved by a load such as a resistor. How can the resistor absorv
determine whether a three bit number , a3,a2,a1 is equal to another number b3,b2,b1 or if it is greater than that number (We do not need an output for less than) a)Show how the 7485 would be connect
For the same functions,we have available as many of the decoders described below as needed plus 2 eight-input OR gates.Show a block diagram for this implementation. All inputs areavailable both unc
Using 3kohm resistors and ideal op amps, design a low-passunity-gain butterworth filter that has a cutoff frequency of 20 khz and is down at least 25 dB at 100 khz.
Design a circuit to multiply two 2-bit numbers - a,b and c,d and produce a 4-bit product -- w,x,y,z. Show a truth table and the equations.
In anticipation of performing Monte Carlo analysis, each resistor can be represented as Ract = Rnom*(1+0.02*(2*rand-1)) where Ract and Rnom are the actual and nominal resistances and rand is a rando
A voltage divider having a gain G = Vo/Vs = 0.8 consists of 5% resistors Ra and Rb having nominal values of 100 Ohms and 400 Ohms. A worst case analysis shows that Gmin<G<Gmax. Determine the v
Derive a minimum-cost realization of the four-variable function that is equal to 1 if exactly two or exactly three of its variables are equal to 1; otherwise it is equal to 0!
Let F(z) = a0 + a1z-1 +a2z-2 denote the composite transfer function of the transmitter, channel and the matched filter in this ultra wide band system. Find a two tap digital equalizer Heq(z) =w0 + w
The coherent detector for the demodulation of DSB-SC fails to operate satisfactorily if the modulator experiences spectral overlap, explain the reason for this failure.
Design a unity-gain bandpass filter using a cascade connection, togive a center frequency of 50 krad/sec and a bandwidth of 300krad/sec. Use 150 μF capacitors. Specify ωc1,ωc2, RL, an
What is the out put voltage of an op amp circut if it has an ambient temperature of 50 degrees celcius and the thermistor Rt resistance is 810 ohms, The voltage in is positive 5 VDC and the only oth
The tungsten filament of an incandescent lamp had aresistance of 7 ohms at a room temperature of 24oC. When it is connected to the electric source the resistance rises to 96ohms. Compute the operati
After several hours of operation, the resistance has increased to 170 ohms. Determine the temperature rise and the final temperature of the machine.
No. 6 AWG copper wire has an area of 13.30mm2 and the resistivity at 200C is 1.75 x10-6 ohm-cm. Determine the length of No. 6 copper wireof the same temperature to give a resistance of 0.12 ohm.
A coil of copper wire (ρ=10.37 micro-ohm-CM/ft) hasa length of 182.88 meters. What is the length of aluminum conductor(ρ=17 micro-ohm-CM/ft) of the same area and resistance asthose of copper
The resistivity of copper is 1.724 micro-ohm-cm at200C. Determine for copper at 200C the resistance (a) of a cylindrical conductor 1 meter long and having a diameter of 1mm; (b) a rod 2 meters long
In a toaster the heating unit is a Nichrome wire whose resistance is 660 micro-ohm-CM/ft and resistance is 20 ohms.Determine the resistance of copper conductor of equalcross-section, but 10 times as
The specific resistivity of brass is 11.4 micro-ohm-cm. Compare the resistance of brass rod A and B if rod A is 1 meterlong and has an area of 2 sq. cm and rod B is ½ meter longand has an are
A certain appliance has a potential difference of 100volts while getting a current of 1.5 amperes. Calculate the rate at which energy is changing in this appliance.