Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
A typical propane tank that we use for barbeque initially contains a pressure of 10 psi. The pressure is low, so we take it to the local store to fill the tank with more propane. After filling,the p
The "sea-level adjusted" pressure at the airport was about 30.57 inches of mercury. Assuming the density of air is 1.30 kg/m3 and the gas constant for air is 287. J/(kg K), calculate the temperature
The depth to water in A is 210 ft, in B is300 ft, and C is 230 ft. Determine the direction of ground water flow through the triangle ABC and calculate the hydraulic gradient. If the aquifer hydrauli
calculate the cracking moment (resisting moment) for an unreinforcedconcrete beam that is 10 in. wide, 16 in. high. assume normal weight concrete with 3000 psi = f prime sub c. use the internal coup
A sample with a measured background level (Bi) of 22 mg/l was spiked with the equivalent of 30 mg/l without appreciably changing the sample volume. The result for the spiked sample (Ai) was 49.2 mg/
A second load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the post are dAB= 1.25 in, tAB= 0.5 in, dBC= 2.25 in and tBC= .375
the unit weight of normal weight reinforced concrete is commonly assumed to be 150 lb/ft cubed. find the weight per lineal foot (lb/ft) for a normal weight reinforced concrete beam that: a. has a re
If a car engine is turning at 4000 rpm, the transmission gear ratio is 3:1 and the final drive ratio is 4:1. (a) what is the speed in rpm of the car wheels and (b) the vehicle speed if the tire radi
At standard pressure, 14.7 psi absolute, it holds 0.5-slug of water; rho = 1.94 slug/ft^3. For K = 300,000 psi, when it is filled, how many slugs of water must be added to increase the pressure to 1
What is the bulk modulus of a liquid that has a density increase of 0.02 percent for a pressure increase of 1000 lb/ft^2
the engine develops a maximum torque of 210ft-lb at 3600 rev/min. what is the maximum grade this vehicle could ascend, on a paved surface, while the engine is developing maximum torque (assume that
Create a precedence (activity-on-node) diagram based off the attached activity list. You must follow the below recommendations as we discussed in class. 1) draw nodes as rectangles. It helps define
A lagoon with a volume of 1200 m^3 has been receiving a steady flow of a conservative waste at a rate of 100m^3/day for a long enough time to assume that steady-state conditions apply. The waste ent
If there are 50 vehicles on a 4000-ft highway lane and the average time headway between two adjacent vehicles is 2.2 seconds. A) Calculate traffic density in vehicle/mile (vpm) and average space headw
The acceleration of a particle is defined by the relation a= -0.7v where a is expressed in in/s2 and v in in/s. Knowing that t= o the velocity is 30in/s, determine 1.) the distance the particle will
The vertical velocity of the box at the time that it hits the surface is v= 5m/s. After impact the camera experiences an acceleration of a = -kx, where k is a constant and x is the compression of th
A u-tube manometer is used to measure the pressure of a vessel under vacuum. Assume the manometer is open to atmospheric pressure (101.325 kPa) and the density of the fluid in the ma
A stainless steel tube with an outside diameter of 65 mm and a wall thickness of 5 mm is used as a compression member. If the axial normal stress in the member must be limited to 180 MPa, determine
A body weighing 120 lb with a flat surface area of 2 ft^2 slides down a lubricated inclined plane making a 30 degree with the horizontal. For a viscosity of 0.002 lb*s/ft^2 and body speed of 3 ft/
A fluid film 0.1 mm thick separates solid and surface. The fluid viscosity is 0.04 N*sec/m^2. Assuming the velocity distribution in the film is linear, find the terminal velocity of the block. The a
A pile resists the tension developed by three stay cables for a major tent (Membrane) Structure. Assuming no bending is desired in the pile (no resultant horizontal component), what is the magnitude
Reciprocal leveling gives the following readings in feet from a setup near A: on A, 2.071; on B, 8.254, 8.259 and 8.257. At the setup near B: on B, 9.112; on A, 2.926, 2.930 and 2.927. The elevation
CALCULATE THE REQUIRED DIAMETER OF STEEL TIE RODS NECESSARY TO SUPPORT A BALCONY. EACH ROD, SUSPENDED FROM A ROOF TRUSS, SUPPORTS A FLOOR AREA OF 7.0m^2. THE COMBINED BALCONT FLOOR LOAD IS 10.5 kPa
a cantilevered bean has a lenght of L, a cross section area of A, and a flecural rigidity of EI. The free end is free to rotate and displace due to bending. derive the stiffnes of the cantilevered b
Determine the actual field weight required to mix a 4 bag mix using the mix proportions given below. The excess moisture contet of the sand is 6% and that of the gravel is 2% Component