What would be the speed of the water coming from pipe, Mechanical Engineering

+44 141 628 6080
[email protected]

What would be the speed of the water coming from pipe

A Dam across a river dams up a lake 300 m higher than the river downstream. The electric generators driven by water-powered turbines deliver 1600 MW of power. If the water is 19.5 degree C,

1) Find the pressure applied to the turbine

2) Find the min. amount of water that is running through the turbines.

3) If the water comes out from a pipe with a radius 50 cm. What would be the speed of the water coming from the pipe?

View Complete Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: What would be the speed of the water coming from pipe

Reference No:- TGS0738771

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : What is the value predicted by the ideal gas law

Find the specific volume of steam (in m^3/kg) at 2.5 MPa and 283 degrees C. What is the value predicted by the ideal gas law?

Q : Determine the rate of heat loss from the duct

An 8-m long, unisulated square duct of cross sectional 0.2-m x 0.2-m and relative roughness 10^-8 passes through the attic space of a house. Hot air enters the duct at 1 atm and 80 C at a volume flow rate of 0.15m^3/s.

Q : Fraction of the transmitted energy due to uncollided photons

A beam of 800 keV gamma is mormally incident on a sheet of lead 12mm thick. the rate of energy transmission is 3x10^5 MeV s^-1. What fraction of the transmitted energy is due to uncollided photons?

Q : Find temperature in vessel and quality just before rupture

The vessel will rupture if the pressure reaches 5 Mpa. What is the initial pressure and quality? What is the temperature in the vessel and the quality just before rupture?

Q : What would be the speed of the water coming from pipe

A Dam across a river dams up a lake 300 m higher than the river downstream. The electric generators driven by water-powered turbines deliver 1600 MW of power.

Q : What is the final temperature and work done

Additional heat is added until the pressure reaches 1.2 MPa. How much work is done? What is the final temperature at 1.2 MPa?

Q : Find final volume and work for isothermal process

The gas may be considered idal at these conditions. Find the final volume and the work for And isothermal process (PC = constant)

Q : What microstructure would be expected

Fine pearlite and a small amount of martensite are found in a quenched 1080 steel. What microstructure would be expected if we had used a low alloy, 0.2% C steel? What microstructure would be expected if we had used a 4340 steel?

Q : Find heat and work quantities for each of the four processes

Draw the P-V and T-S diagrams of the cycle and determine (a) p, T and v of the four state points, (b) heat and work quantities for each of the four processes, and (c) the cycle thermal efficiency.

1953778

Questions
Asked

3,689

Active Tutors

1445992

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: What would be the speed of the water coming from pipe

Reference No:- TGS0738771

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : What is the value predicted by the ideal gas law

Q : Determine the rate of heat loss from the duct

Q : Fraction of the transmitted energy due to uncollided photons

Q : Find temperature in vessel and quality just before rupture

Q : What would be the speed of the water coming from pipe

Q : What is the final temperature and work done

Q : Find final volume and work for isothermal process

Q : What microstructure would be expected

Q : Find heat and work quantities for each of the four processes

Nursing diagnosis of deficient fluid volume

What is meant by an incomplete abortion

Which sign indicates a child is a victim of bullying

Pregnant client about having a chorionic villus sampling

Discuss nursing diagnosis of deficient fluid volume

Defining characteristics of this diagnostic label

What is meant by an incomplete abortion

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: What would be the speed of the water coming from pipe

Reference No:- TGS0738771

Recent Questions Asked Mechanical Engineering

Q : What is the value predicted by the ideal gas law

Q : Determine the rate of heat loss from the duct

Q : Fraction of the transmitted energy due to uncollided photons

Q : Find temperature in vessel and quality just before rupture

Q : What would be the speed of the water coming from pipe

Q : What is the final temperature and work done

Q : Find final volume and work for isothermal process

Q : What microstructure would be expected

Q : Find heat and work quantities for each of the four processes

Asked Questions