What wall thickness is required, Mechanical Engineering

+44 141 628 6080
[email protected]

What wall thickness is required

The pressure inside the cylinders of a diesel engine reaches a maximum pressure of 100atm during combustion. The diameter of the cylinder is about 5 inches. If a factor safety(FS) of 11 is required and the cylinder walk material is 4340-HR steel (yield stress 910 MPa =910E6 = 910x 10^6 N/m^2), what wall thickness is required?

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: What wall thickness is required

Reference No:- TGS0738119

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Find static pressure of airstream away from effect building

If the internal pressure equals that of the free stream static pressure, what is the total force on the plane of glass 1m x 3m located in this regin?

Q : Find pressure recorded by gage that measures difference

What is the pressure recorded by a gage that measures the difference between the stagnation pressure and the static pressure?

Q : Determine the magnitude of the current density

A 5.00 m length of 1.8 mm diameter wire carries a 700 mA current when 18.0 mV is applied to its ends. Assume the drift velocity is 1.7 × 10-5 m/s. Determine the magnitude of the current density

Q : Why the flow is frictionless and adiabatic

For air flowing in a converging-diverging nozzle, the pressure and temperature at the inlet are 14.7 psia and 70°F. At some location in the diverging portion of the nozzle, the pressure is 1.37 psia.

Q : What wall thickness is required

The pressure inside the cylinders of a diesel engine reaches a maximum pressure of 100atm during combustion. The diameter of the cylinder is about 5 inches.

Q : Find total change in entropy of universe due to cooling

If the surroundings are treated as a thermal reservoir, what is the total change in entropy of the universe due to this cooling process?

Q : Why the stress exceeding the yield stress of the material

At what pressure(give type: tension, compression, or shear) would this cylinder fail( due to the stress exceeding the yield stress of the material) if the high pressure were inside the cylinder?

Q : Find volumetric flow rate into the compressor

Determine: The turbine power output The fraction of the turbine output used to drive the compressor. The mass flow rate of air into the compressor. The volumetric flow rate into the compressor.

Q : What would the wall thickness need to be to withstand

If the vessel had a yield strength in compression in equal to that of 4340-HR steel (901 x 10^6Pa) and a safety factor of 2 was employed, what would the wall thickness need to be to withstand the pressure at the bottom of Challenger Deep (1086 atm

1959793

Questions
Asked

3,689

Active Tutors

1435173

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: What wall thickness is required

Reference No:- TGS0738119

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Find static pressure of airstream away from effect building

Q : Find pressure recorded by gage that measures difference

Q : Determine the magnitude of the current density

Q : Why the flow is frictionless and adiabatic

Q : What wall thickness is required

Q : Find total change in entropy of universe due to cooling

Q : Why the stress exceeding the yield stress of the material

Q : Find volumetric flow rate into the compressor

Q : What would the wall thickness need to be to withstand

Medication for postoperative nausea and vomiting

Child prescribed prednisone for exacerbation of asthma

What if a parent of hispanc origin informs nurse of plans

How health care reimbursement is delivered

How to improve overall health of elementary school children

How would you instruct the patient to taper off clonazepam

How to prevent interference with an intravenous infusion

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: What wall thickness is required

Reference No:- TGS0738119

Recent Questions Asked Mechanical Engineering

Q : Find static pressure of airstream away from effect building

Q : Find pressure recorded by gage that measures difference

Q : Determine the magnitude of the current density

Q : Why the flow is frictionless and adiabatic

Q : What wall thickness is required

Q : Find total change in entropy of universe due to cooling

Q : Why the stress exceeding the yield stress of the material

Q : Find volumetric flow rate into the compressor

Q : What would the wall thickness need to be to withstand

Asked Questions