What is the ph of solution by mixing formic acid, Chemistry

+44 141 628 6080
[email protected]

What is the ph of solution by mixing formic acid

A buffer (pH 3.70) was prepared by mixing 1.00 mole of formic acid and 1.00 mole of sodium formate to form an aqueous solution with a total volume of 1.00 L. To 400 mL of this solution was added 50.0 mL of 1.00 M NaOH. What is the pH of this solution?

Request for Solution File

Ask an Expert for Answer!!

Chemistry: What is the ph of solution by mixing formic acid

Reference No:- TGS0428671

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Chemistry

Q : How much calcium silicate would be formed as by-product

How much calcium silicate would be formed as a by-product? How much sand would be used up in the same reaction?

Q : What volume would be occupied by a 21.8 g sample of osmium

Osmium has a density of 22.6 g/cm3. What volume would be occupied by a 21.8 g sample of osmium?

Q : Determine the magnitude t of the applied torque

Knowing that the tank contains compressed air under a pressure of 8 MPa, determine the magnitude T of the applied torque for which the maximum normal stress in the tank is 75 MPa.

Q : What is the mass of the piece of copper

Copper has a specific heat of 0.092 cal/(g·°C). When 52.7 cal of heat is added to a piece of copper, the temperature increases from 22.4°C to 38.6°C. What is the mass of the piece of copper ?

Q : What is the ph of solution by mixing formic acid

A buffer (pH 3.70) was prepared by mixing 1.00 mole of formic acid and 1.00 mole of sodium formate to form an aqueous solution with a total volume of 1.00 L.

Q : What is the partial pressure of gas

Nitrogen dioxide (NO2) cannot be obtained in a pure form in the gas phase because it exists as a mixture of NO2 and N2O4. At 25°C and 0.98 atm, the density of this gas mixture is 2.7 g/L. What is the partial pressure of each gas?

Q : What is the mole fraction of nitrogen in the mixture

A 10.9-g mixture of nitrogen and carbon dioxide is found to occupy a volume of 8.88 L when measured at 641.9 mmHg and 28.5oC. What is the mole fraction of nitrogen in this mixture?

Q : Determine mass flow rate of the steam

Steam enters the first-stage turbine shown in Fig. 2 at 40 bar and 500°C with a volumetric flow rate of 90 m3/min. Steam exits the turbine at 20 bar and 400°C.

Q : Volume of a component

The volume of a component is to be measured by a process whose uncertainty is 0.05 ml. If 25 independent measurements are made and the average of these is used to estimate the volume, what will the uncertainty be?

1937880

Questions
Asked

3,689

Active Tutors

1432571

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Chemistry: What is the ph of solution by mixing formic acid

Reference No:- TGS0428671

Have a Question? (oR Write a Review)

Recent Questions Asked Chemistry

Q : How much calcium silicate would be formed as by-product

Q : What volume would be occupied by a 21.8 g sample of osmium

Q : Determine the magnitude t of the applied torque

Q : What is the mass of the piece of copper

Q : What is the ph of solution by mixing formic acid

Q : What is the partial pressure of gas

Q : What is the mole fraction of nitrogen in the mixture

Q : Determine mass flow rate of the steam

Q : Volume of a component

Investigate the cause of the recent werewolf attacks

Describe marxist theory and psychology of addiction

Explain framers decisions in creating the constitution

Federal bureaucracy has to put up with a lot of red tape

What power of recognition when it comes to office president

What right ordinance power give to the president

Analyze leadership of organization during particular event

Request for Solution File

Ask an Expert for Answer!!

Chemistry: What is the ph of solution by mixing formic acid

Reference No:- TGS0428671

Recent Questions Asked Chemistry

Q : How much calcium silicate would be formed as by-product

Q : What volume would be occupied by a 21.8 g sample of osmium

Q : Determine the magnitude t of the applied torque

Q : What is the mass of the piece of copper

Q : What is the ph of solution by mixing formic acid

Q : What is the partial pressure of gas

Q : What is the mole fraction of nitrogen in the mixture

Q : Determine mass flow rate of the steam

Q : Volume of a component

Asked Questions