Sketch mohr-s circle for the state of stress, Mechanical Engineering

+44 141 628 6080
[email protected]

Sketch mohr-s circle for the state of stress

The principal stresses at a given point are sigma_1 = 10 MPa, sigma_2 = ?100 MPa. Sketch Mohr's circle for this state of stress and determine the normal stress on a plane inclined at an angle µ to the principal plane 1. Hence find the range of values of µ for which the normal stress is tensile.

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Sketch mohr-s circle for the state of stress

Reference No:- TGS0740249

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Calculate the ratio of the etched and original crack tip

Calculate the ratio of the etched and original crack tip radii if the fracture strength is increased by a factor of 3 when 46.0% of the crack length is removed.

Q : Calculate the value of the damping force

A mass of 55 kg is suspended from a spring of stiffness 83.5 kg/cm. A dash pot is fitted and it is found that the amplitude of the vibration diminishes to 1/5 of its original value after 2 complete vibrations.

Q : Length of the prediction interval

A research engineer for a tire manufacturer is investigating tire life for a new rubber compound and has built 16 tires and tested them to end-of-life in a road test.

Q : What will be the amplitude of vibration of the engine

An engine of mass 180 kg is to be supported on four helical springs. When the engine speed is 900 rpm, there is a primary vertical periodic disturbing force of maximum value 300 N due to the unbalanced reciprocating weights.

Q : Sketch mohr-s circle for the state of stress

Sketch Mohr's circle for this state of stress and determine the normal stress on a plane inclined at an angle µ to the principal plane 1. Hence find the range of values of µ for which the normal stress is tensile.

Q : With what speed does mass hit the ground bottom of cliff

The combined mass is shot horizontally off the cliff. With what speed does the mass hit the ground at the bottom of the cliff?

Q : Calculate the amplitude of the oscillation

Calculate the amplitude of the oscillation which may be allowed if the maximum permissible intensity of shearing stress in the wire is 140 MN/m2

Q : What is the wavelength of the sound

A tuning fork vibrates at a frequency of 256 Hz. What is the wavelength of the sound coming from the fork when the air temperature is a) 0oC and b) 20oC

Q : Determine amount of heat transfer for rigid tank

Neglecting kinetic and potential energy effects, determine: (a) The amount of heat transfer, in kJ and (b) The mass of vapor that escapes, in kg.

1958341

Questions
Asked

3,689

Active Tutors

1456652

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Sketch mohr-s circle for the state of stress

Reference No:- TGS0740249

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Calculate the ratio of the etched and original crack tip

Q : Calculate the value of the damping force

Q : Length of the prediction interval

Q : What will be the amplitude of vibration of the engine

Q : Sketch mohr-s circle for the state of stress

Q : With what speed does mass hit the ground bottom of cliff

Q : Calculate the amplitude of the oscillation

Q : What is the wavelength of the sound

Q : Determine amount of heat transfer for rigid tank

Picot question to address mental health disparity

Statement regarding foods selected in a restaurant

Male complaints of cough, chills, fever, shortness of breath

How does malnutrition impact our health

What data systems could be implemented to improve care

Relationship between poverty and career decision-making

Which children are disproportionately afflicted

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Sketch mohr-s circle for the state of stress

Reference No:- TGS0740249

Recent Questions Asked Mechanical Engineering

Q : Calculate the ratio of the etched and original crack tip

Q : Calculate the value of the damping force

Q : Length of the prediction interval

Q : What will be the amplitude of vibration of the engine

Q : Sketch mohr-s circle for the state of stress

Q : With what speed does mass hit the ground bottom of cliff

Q : Calculate the amplitude of the oscillation

Q : What is the wavelength of the sound

Q : Determine amount of heat transfer for rigid tank

Asked Questions