Probability of a manufacturing defect, Basic Statistics

+44 141 628 6080
[email protected]

Probability of a manufacturing defect

The probability of a manufacturing defect in an aluminum beverage can is .00009. If 100,700 cans are produced, find the following probabilities.

(a) At least eight defective cans. (Round your answer to 4 decimal places.)

(b) At least nine defective cans. (Round your answer to 4 decimal places.)

Request for Solution File

Ask an Expert for Answer!!

Basic Statistics: Probability of a manufacturing defect

Reference No:- TGS0739228

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Basic Statistics

Q : What is the angular magnification of the lense

To read the text you hold a magnifying glass with focal length f=3cm infront of your eye and place text at the focal point of the lens. What is the angular magnification of the lense?

Q : How much force is required to tip off pole

Also what wind speed can tip off this pole if we consider the wind is maximum at the top of the pole.Consider the total weight to be 100lb.

Q : Weekly amount spent on repairs

Suppose thw weekly amount spent on repairs at a certain computer is normally distributed with a mean of $300 and a standard deviation $20

Q : What can be said about the lens and location of object

Some light rays from a small object sitting on the optical axis of a lens pass through a lens and then all of the rays emerging from the lens travel parallel to the optical axis. What can be said about the lens and the location of the object?

Q : Probability of a manufacturing defect

The probability of a manufacturing defect in an aluminum beverage can is .00009. If 100,700 cans are produced, find the following probabilities.

Q : Calculate the cumulative density function

The time to failure of a battery in hours of a personal handheld music device follows an exponential distribution. The expected battery life is 2000 hours. Calculate the cumulative density function, F(x)=P(X<x).

Q : How to evaluate the work required and the heat transfer

Air enters a compressor operating at steady state with a volumetric flow rate of 8 m3/min at 23°C and 0.12 MPa. The air is compressed isothermally without internal irreversibilities, exiting at 1.5 MPa.

Q : Find the electric field at the remaining corner

Find the electric field at the remaining (upper right corner).(Assume the +x axis is directed to the right and the +y axis is directed upward.)

Q : What is the size of the magnetic field

A lightning bolt with 20,000A of current in a circular cross section of radius 5mm strikes the ground 1m from where you are standing. What is the size of the magnetic field where you are standing? (Neglect the Earth's magnetic field.)

1922125

Questions
Asked

3,689

Active Tutors

1429095

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Basic Statistics: Probability of a manufacturing defect

Reference No:- TGS0739228

Have a Question? (oR Write a Review)

Recent Questions Asked Basic Statistics

Q : What is the angular magnification of the lense

Q : How much force is required to tip off pole

Q : Weekly amount spent on repairs

Q : What can be said about the lens and location of object

Q : Probability of a manufacturing defect

Q : Calculate the cumulative density function

Q : How to evaluate the work required and the heat transfer

Q : Find the electric field at the remaining corner

Q : What is the size of the magnetic field

Picot question to address mental health disparity

Statement regarding foods selected in a restaurant

Male complaints of cough, chills, fever, shortness of breath

How does malnutrition impact our health

What data systems could be implemented to improve care

Relationship between poverty and career decision-making

Which children are disproportionately afflicted

Request for Solution File

Ask an Expert for Answer!!

Basic Statistics: Probability of a manufacturing defect

Reference No:- TGS0739228

Recent Questions Asked Basic Statistics

Q : What is the angular magnification of the lense

Q : How much force is required to tip off pole

Q : Weekly amount spent on repairs

Q : What can be said about the lens and location of object

Q : Probability of a manufacturing defect

Q : Calculate the cumulative density function

Q : How to evaluate the work required and the heat transfer

Q : Find the electric field at the remaining corner

Q : What is the size of the magnetic field

Asked Questions