Find the diameter of the exit pipe and the power output, Mechanical Engineering

Find the diameter of the exit pipe and the power output

A steady flow of 15 kg/s of high-pressure liquid oil drives a hydraulic motor at the steady-state-steady-flow conditions shown below. Heat loss from the motor to the surroundings is 5 kW. This is not a quasi-equilibrium process. Use standard gravity, g = 9.81 m/s2.

Find the diameter of the exit pipe, D2 = ________ (m) and the power output, Wcv & out = _________ (kW).

LIQUID kPa oC m/s m

1 8000 40 25 20

2 500 42 25 15

View Complete Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Find the diameter of the exit pipe and the power output

Reference No:- TGS0735133

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : How leave at a pressure and temperature

Exhaust gases enter the regenerator at a pressure of 140 KPa, temperature of 800 K and leave at a pressure and temperature of 130 KPa and 600 K. Treat exhaust gases as air.

Q : Determine the depth at which the pipe was stuck

At the same time, measurements showed that the pipe elongated by 0.35 mm in a 200 mm gauge length. Determine the depth at which the pipe was stuck. Assume the cross-section of the pipe is constant with depth.

Q : Sample size required to construct

Assuming that the population proportion p is near 0.3, find the sample size required to construct 90% confidence interval for p with margin of error 0.03. Repeat the same calculations if p is close to 0.5.

Q : Calculate the percent of energy used per day

Electronic devices use electrical energy even when they are on standby. Calculate the percent of energy used per day for the following entertainment equipment in the standby mode assuming that they are plugged in all the time.

Q : Find the diameter of the exit pipe and the power output

A steady flow of 15 kg/s of high-pressure liquid oil drives a hydraulic motor at the steady-state-steady-flow conditions shown below. Find the diameter of the exit pipe, and the power output, Wcv & out?

Q : What are the electronic contribution

The heat capacity of silver, measured at a temperature of 4 K, is 0.0134 J/(mole ·K). The Debye temperature of silver is 225 K. What are the electronic contribution (J/(mole ·K)) to the heat capacity of silver at 2 K?

Q : Null and alternative hypothesis for testing

Report shows that 45% of all US households owned 2 cars in 2000. Set up the null and alternative hypothesis for testing whether the percentage of households cars has

Q : What is the temperature at the trailing edge of the plate

The average plate temperature of a ?at plate of length L with constant heat ?ux with air at 20? C ?owing over it at a certain velocity was found to be 50 ? C. What is the temperature at the trailing edge of the plate?

Q : Calculate the heat lost from the strip per unit depth

Air at 15 ? C ?ows over a ?at plate. A heater strip 10 cm long is placed on the plate at a distance 15 cm from the leading edge. The local heat transfer coe?

1938767

Questions
Asked

3,689

Active Tutors

1441956

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Find the diameter of the exit pipe and the power output

Reference No:- TGS0735133

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : How leave at a pressure and temperature

Q : Determine the depth at which the pipe was stuck

Q : Sample size required to construct

Q : Calculate the percent of energy used per day

Q : Find the diameter of the exit pipe and the power output

Q : What are the electronic contribution

Q : Null and alternative hypothesis for testing

Q : What is the temperature at the trailing edge of the plate

Q : Calculate the heat lost from the strip per unit depth

What facilitate a stable, safe, pain-free cervical posture

Interview a bsn-prepared nurse

Does the patient have pearl pupils

Teaching a client with osteoarthritis about self-management

Nurse teaching client with hiv receiving antiretroviral

Nurse is planning care for client who had hip replacement

Describe nurse is caring for a client with hemophilia

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Find the diameter of the exit pipe and the power output

Reference No:- TGS0735133

Recent Questions Asked Mechanical Engineering

Q : How leave at a pressure and temperature

Q : Determine the depth at which the pipe was stuck

Q : Sample size required to construct

Q : Calculate the percent of energy used per day

Q : Find the diameter of the exit pipe and the power output

Q : What are the electronic contribution

Q : Null and alternative hypothesis for testing

Q : What is the temperature at the trailing edge of the plate

Q : Calculate the heat lost from the strip per unit depth

Asked Questions