Determine the thickness of steel plate required, Mechanical Engineering

+44 141 628 6080
[email protected]

Determine the thickness of steel plate required

Determine the thickness of steel plate required for a 2m diameter cylindrical boiler with hemispherical ends if the tensile and shear stresses in the plate are not to exceed 85 Mpa and 40 Mpa. respectively, when the internal pressure in the boiler is 1.5Mpa

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine the thickness of steel plate required

Reference No:- TGS0738685

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Calculate the factor of safety the designer must have used

Calculate the factor of safety the designer must have used. The elongation in a 2-in speciman of ASTN No. 40 at failure is approximately 0.5%-1.0%.

Q : Is there any heat loss from the steam turbine

The steam at the inlet is 20 bar absolute with superheat of 135 C . The steam at the outlet is 1 bar absolute and 100 C. The velocity of the steam at inlet is 3m/s, and 12 m/s at the outlet.

Q : What is the maximum heating rate for nucleate boiling

Saturated water at 1 atm and velocity 2 m/s flows over a cylindeical heating element of diameter 5 mm. What is the maximum heating rate (W/m) for nucleate boiling?

Q : Find if component is safe for design factor at two points

A component is made of a brittle material that has prperties Sut=30 ksi and Suc= 90ksi. Use MNST, BCMT, MMT to determine if the component is safe for a design factor 1.5 at two points.

Q : Determine the thickness of steel plate required

Determine the thickness of steel plate required for a 2m diameter cylindrical boiler with hemispherical ends if the tensile and shear stresses in the plate are not to exceed 85 Mpa and 40 Mpa.

Q : Determine impulse provided to person-plateform system

Neglecting any resistance to the motion of the plateform due to the water, determine the impulse provided to the person/plateform system by the rope when the rope becomes taut.

Q : Which energy is rejected by heat transfer to cold reservior

Compare theresults of part(a) with those of a resersible power cycle operating between these reserviors and receiving the same rate of heat transfer from the hot reservior.

Q : Find the quality of a saturated wet mixture

Find the quality (x) of a saturated wet mixture with a specific volume of 0.175 ft^3/lbm at a pressure of 1000 psig. State the answer in the proper units. Show all of your work. You need to use a steam table to solve the problem

Q : Calculate the temperature change that can be tolerated

A machining-center spindle and tool extend 10in. from their machine-tool frame. calculate the temperature change that can be tolerated in order to maintain a tolerance of 0.001in. in machining. assume that the spindle is made of steel.

1934578

Questions
Asked

3,689

Active Tutors

1418197

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine the thickness of steel plate required

Reference No:- TGS0738685

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Calculate the factor of safety the designer must have used

Q : Is there any heat loss from the steam turbine

Q : What is the maximum heating rate for nucleate boiling

Q : Find if component is safe for design factor at two points

Q : Determine the thickness of steel plate required

Q : Determine impulse provided to person-plateform system

Q : Which energy is rejected by heat transfer to cold reservior

Q : Find the quality of a saturated wet mixture

Q : Calculate the temperature change that can be tolerated

How protein is an essential part of our health

Discuss about health information exchanges in the niles

Discuss education and care services national regulations

How to determine if there is a quality issue

What inter-professional involvement needs to be considered

Why should contraception be a reproductive right

Problem regarding childhood education and care services

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine the thickness of steel plate required

Reference No:- TGS0738685

Recent Questions Asked Mechanical Engineering

Q : Calculate the factor of safety the designer must have used

Q : Is there any heat loss from the steam turbine

Q : What is the maximum heating rate for nucleate boiling

Q : Find if component is safe for design factor at two points

Q : Determine the thickness of steel plate required

Q : Determine impulse provided to person-plateform system

Q : Which energy is rejected by heat transfer to cold reservior

Q : Find the quality of a saturated wet mixture

Q : Calculate the temperature change that can be tolerated

Asked Questions