Determine appropriate values for the disk inside dimmeter, Mechanical Engineering

Determine appropriate values for the disk inside dimmeter

A disk clutch is to be designed for transmitting a torqueof 85N.m space restrictons limit the outside disk diameter to 100m.m.Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa.Determine appropriate values for the disk inside dimmeter,the total number of disks and the actuating force?

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine appropriate values for the disk inside dimmeter

Reference No:- TGS0426915

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Determine the actual strain

You have a 120 Ω quarter bridge 2 wire set up with Sg=2.10 and an unknown lead wire resistance. A 59880Ω calibration resistor is switched in parallel to the gage only and a recording instrument is set to give a -100 mm deflection for this

Q : Calculate the pressure of dry oxygen

Calculate the pressure of dry oxygen. If the total pressure of oxygen generated over water is measured to be 638 torr and the temperature is 22 degress celcius?

Q : A solution consisting of four parts

A solution consisting of four parts 70% HNO3 , four parts 49% HF, and two parts CH3COOH is used to etch silicon. If the solution is held at room temperature, what etch rate would you expect? If the compound is to remain at two parts CH3COOH, what

Q : What is the pressure of the gas in the second tank

The gas is transferred to a different tank with a volume of 925 mL and 325 K. What is the pressure of the gas in the second tank?

Q : Determine appropriate values for the disk inside dimmeter

Q : What can be said about the reaction when react with oxygen

What can be said about the following reaction, C5H12(l)+O2(g) CO(g)+H2O(l), if 13.3 g of C5H12 is allowed to react with 5.0 g of oxygen?

Q : Energy gap between the conduction band

The energy gap between the conduction band and the valence band is large for

Q : Find the final condition of steam and the pipe diameters

Steam at 10bar and 0.95 dry flows at 130 m/sec in a pipe. It is throttled to 8 bar and the flow rate is 12 kg/sec. Assuming velocity in the pipe on the down stream side of the valve is 160 m/sec.

Q : Design a plc program and prepare a typical i o connection

A motor must be started and stopped from any one of three start/stop pushbotton stations.Each start/stop station contains one NO start pushbutton and one NC stop pushbutton.Motor OL contacts are to be hardwired.

1922759

Questions
Asked

3,689

Active Tutors

1434916

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine appropriate values for the disk inside dimmeter

Reference No:- TGS0426915

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Determine the actual strain

Q : Calculate the pressure of dry oxygen

Q : A solution consisting of four parts

Q : What is the pressure of the gas in the second tank

Q : Determine appropriate values for the disk inside dimmeter

Q : What can be said about the reaction when react with oxygen

Q : Energy gap between the conduction band

Q : Find the final condition of steam and the pipe diameters

Q : Design a plc program and prepare a typical i o connection

How client is at risk at developing an infection

Which cause of amenorrhea should the nurse suspect most

Patient reported a scaly, circumscribed, erythematous lesion

Discuss potential diversity in group that you anticipate

Identify a specific health outcome or public health concern

What if auscultate crackles in the poster left lover lobe

Struggle with providing proper hygiene for the patients

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine appropriate values for the disk inside dimmeter

Reference No:- TGS0426915

Recent Questions Asked Mechanical Engineering

Q : Determine the actual strain

Q : Calculate the pressure of dry oxygen

Q : A solution consisting of four parts

Q : What is the pressure of the gas in the second tank

Q : Determine appropriate values for the disk inside dimmeter

Q : What can be said about the reaction when react with oxygen

Q : Energy gap between the conduction band

Q : Find the final condition of steam and the pipe diameters

Q : Design a plc program and prepare a typical i o connection

Asked Questions