Calculate distance between hinged point and bottom of gate, Mechanical Engineering

+44 141 628 6080
[email protected]

Calculate distance between hinged point and bottom of gate

Water gate is hinged at point O. Angle between the gate and the ground is given: alpha =60 degrees. The gate opens when water levels reaches H=2m on the left and h=0.4m on the right. Calculate distance x between the hinged point O and the bottom of the gate.

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Calculate distance between hinged point and bottom of gate

Reference No:- TGS0717314

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Which costs are relevant and which are not relevant

Costs associated with two alternatives, code-named Q and R, being considered by Albiston Corporation are listed below: Alternative Q Alternative R Supplies costs......... $65,000 $65,000 Power costs............ $30,000 $29,000

Q : What outside diameter required to give outer surface stress

What is the nominal shear stress at the surface? If a hallow shaft of inside diameter 0.85 times outside diameter is used, what outside diameter would be required to give the same outer surface stress?

Q : What is the capacitance of the two wires

A capacitor is consists of two short sections of parallel wires in air. One wire is found to be of the voltage of 48 V and the other -48. They carry equal and opposite charge of magnitude 65 pC. What is the capacitance of the two wires?

Q : Discuss the remaining income or loss to be shared

Martha and Jones have capital balances on January 1 of $50,000 and $40,000, respectively. The partnership income-sharing agreement provides for (1) annual salaries of $20,000 for Martha and $12,000 for Jones,

Q : Calculate distance between hinged point and bottom of gate

The gate opens when water levels reaches H=2m on the left and h=0.4m on the right. Calculate distance x between the hinged point O and the bottom of the gate.

Q : What is the thermal current in the copper bar

A copper bar 2.5 m long has a circular cross section of radius 2 cm. One end is kept at 80 oC and the other end is kept at 0 oC. The surface of the bar is insulated so that there is negligible heat loss through it. If kcopper = 401 W.m-1.K-1, what

Q : What is the nominal bending stress at the surface

A 2 in diameter straight round shaft is subjected to a bending of 2000 ft.lb a) What is the nominal bending stress at the surface?

Q : Determine the net present value of the project

A project has estimated annual cash flows of $90,000 for three years and is estimated to cost $250,000. Assume a minimum acceptable rate of return of 10%.

Q : What assumption did the analysis in the previous parts

Assume that gasoline costs $3.60 per gallon and you plan to keep either car for six years. How many miles per year would you need to drive to make the decision to buy the hybrid worthwhile, ignoring the time value of money?

1943058

Questions
Asked

3,689

Active Tutors

1461531

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Calculate distance between hinged point and bottom of gate

Reference No:- TGS0717314

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Which costs are relevant and which are not relevant

Q : What outside diameter required to give outer surface stress

Q : What is the capacitance of the two wires

Q : Discuss the remaining income or loss to be shared

Q : Calculate distance between hinged point and bottom of gate

Q : What is the thermal current in the copper bar

Q : What is the nominal bending stress at the surface

Q : Determine the net present value of the project

Q : What assumption did the analysis in the previous parts

How protein is an essential part of our health

Discuss about health information exchanges in the niles

Discuss education and care services national regulations

How to determine if there is a quality issue

What inter-professional involvement needs to be considered

Why should contraception be a reproductive right

Problem regarding childhood education and care services

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Calculate distance between hinged point and bottom of gate

Reference No:- TGS0717314

Recent Questions Asked Mechanical Engineering

Q : Which costs are relevant and which are not relevant

Q : What outside diameter required to give outer surface stress

Q : What is the capacitance of the two wires

Q : Discuss the remaining income or loss to be shared

Q : Calculate distance between hinged point and bottom of gate

Q : What is the thermal current in the copper bar

Q : What is the nominal bending stress at the surface

Q : Determine the net present value of the project

Q : What assumption did the analysis in the previous parts

Asked Questions