At what grain diameter will lower yield point be given value, Mechanical Engineering

+44 141 628 6080
[email protected]

At what grain diameter will lower yield point be given value

The lower yield point for an iron that has an average grain diameter of 5 x10-2 mm is 135 MPa (19,500 psi). At a grain diameter of 8 x 10-3 mm, the yield point increases to 260 MPa (37,500 psi). At what grain diameter will the lower yield point be 205 MPa (30,000 psi)?

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: At what grain diameter will lower yield point be given value

Reference No:- TGS0737419

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : What are the velocity components of the object

What is the direction of the acceleration? Whats is the mass of the object? If the object is intially at rest, what is the speed after 10.0 s? What are the velocity components of the object after 10.0 s?

Q : Determine the electric power output of plant

The combine turbine-generator efficiency 80 percent. Disregarding the minor losses because large length-to-diameter ratio, determine the electric power output of this plant.

Q : Most common causes of strength degradation

Describe the three most common causes of strength degradation of mechanical components. Give examples of each, with descriptions of methods used to prevent or reduce the chances of failure.

Q : Why neglecting the potential energy effects

Steam enters a well-insulated turbine operating at steady state with negligible velocity at 4 MPa, 320C. The steam expands to an exit pressure of 0.07 MPa and a velocity of 90 m/s. The diameter of the exit is 0.6 m.

Q : At what grain diameter will lower yield point be given value

At a grain diameter of 8 x 10-3 mm, the yield point increases to 260 MPa (37,500 psi). At what grain diameter will the lower yield point be 205 MPa (30,000 psi)?

Q : Uniformly chosen random location

We break a stick at a uniformly chosen random location. Find the probability that the shorter piece is less than 1=5th of the original.

Q : Speed and direction of the balls velocity vector

A ball is thrown from atop a cliff with an initial speed of 30 m/s at an angle of 40o above the horizontal. The cliff is 40 m above level ground. Neglect the effects of air resistance.What is the speed and direction of the ball's velocity vector just

Q : Determine the minimum mass flow rate of the water

Cooling water circulates through a water jacket enclosing a housing filled with electronic components. At steady state, water enters the water jacket at 20oC and exits with a negligible change in pressure at a temperature that cannot exceed 24oC.

Q : Interpretations is most reasonable

A researcher reported a correlation of 1.25 between an IQ test and grades in EPY 6214. Which one of the following interpretations is most reasonable?

1935823

Questions
Asked

3,689

Active Tutors

1430639

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: At what grain diameter will lower yield point be given value

Reference No:- TGS0737419

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : What are the velocity components of the object

Q : Determine the electric power output of plant

Q : Most common causes of strength degradation

Q : Why neglecting the potential energy effects

Q : At what grain diameter will lower yield point be given value

Q : Uniformly chosen random location

Q : Speed and direction of the balls velocity vector

Q : Determine the minimum mass flow rate of the water

Q : Interpretations is most reasonable

Analyze military operation that failed due to poor alignment

Why president should not be permitted to deploy military

Discuss checks-balances on presidents military powers

Selection for the semester-long biographical project

Apply a waiting line model to a business service operation

How to make a big sale to an overseas government client

Give strategies for conducting negotiation between countries

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: At what grain diameter will lower yield point be given value

Reference No:- TGS0737419

Recent Questions Asked Mechanical Engineering

Q : What are the velocity components of the object

Q : Determine the electric power output of plant

Q : Most common causes of strength degradation

Q : Why neglecting the potential energy effects

Q : At what grain diameter will lower yield point be given value

Q : Uniformly chosen random location

Q : Speed and direction of the balls velocity vector

Q : Determine the minimum mass flow rate of the water

Q : Interpretations is most reasonable

Asked Questions